Skip to content

bot du proc #7

Open
Open
bot du proc#7

Description

@jb255
jb255
opened on Aug 2, 2018

> ~ sudo picocom /dev/ttyUSB0 -b 115200

picocom v1.7

port is        : /dev/ttyUSB0
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
escape is      : C-a
local echo is  : no
noinit is      : no
noreset is     : no
nolock is      : no
send_cmd is    : sz -vv
receive_cmd is : rz -vv
imap is        : 
omap is        : 
emap is        : crcrlf,delbs,

Terminal ready
�CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  3 prefetch abort
pc : [<00000004>]	   lr : [<9f764fa0>]
sp : 9f32ef18  ip : 00000020	 fp : 80814a88
r10: 80844f0c  r9 : 9f32ef38	 r8 : 4030cdcc
r7 : 000001f7  r6 : 9f371e38	 r5 : 00000000  r4 : 00000003
r3 : 00000000  r2 : 000001f7	 r1 : 00000426  r0 : 00000000
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32
Resetting CPU ...

resetting ...
CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
## Warning: Unknown environment variable type 'm'
## Warning: Unknown environment variable access method 'a'
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  0 
�CCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
�[B��CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
prefetch abort
pc : [<00000004>]	   lr : [<9f75e560>]
sp : 9f301620  ip : 00000000	 fp : 80814a88
r10: 80844f0c  r9 : 9f32ef38	 r8 : 4030cdcc
r7 : 4030cb7c  r6 : 00000002	 r5 : 9f301894  r4 : 0000000f
r3 : 00000000  r2 : 00000001	 r1 : 9f30184c  r0 : 9f301624
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32
Resetting CPU ...

resetting ...
CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
## Warning: Unknown environment variable type 'm'
## Warning: Unknown environment variable access method 'a'
Could not get PHY for cpsw: addr 0
prefetch abort
pc : [<0000000{>]	   lr : [<f ob;boi>]
sp : f $ }oit  ip : 00000000	 fp : titn{itt
r10: tit{{ ie  r9 : f $ ; $t	 r8 : (  ;e  i
r7 : 00000000  r6 : 00000000	 r5 : f $ }toe  r4 : 0000000 
r3 : 00000000  r2 : 0000000n	 r1 : f $ }t${  r0 : f $ }oie
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32
Resetting CPU ...

resetting ...
CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  0 
U-Boot# ?
?       - alias for 'help'
askenv  - get environment variables from stdin
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BOOTP/TFTP protocol
bootz   - boot Linux zImage image from memory
chpart  - change active partition
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
dfu     - Device Firmware Upgrade
dhcp    - boot image via network using DHCP/TFTP protocol
echo    - echo args to console
editenv - edit environment variable
eeprom  - EEPROM sub-system
env     - environment handling commands
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
ext4load- load binary file from a Ext4 filesystem
ext4ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fatwrite- write file into a dos filesystem
fdt     - flattened device tree utility commands
go      - start application at address 'addr'
gpio    - input/set/clear/toggle gpio pins
gpt     - GUID Partition Table
help    - print command description/usage
i2c     - I2C sub-system
iminfo  - print header information for application image
imxtract- extract a part of a multi-image
itest   - return true/false on integer compare
load    - load binary file from a filesystem
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
ls      - list files in a directory (default /)
md      - memory display
mdio    - MDIO utility commands
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mtdparts- define flash/nand partitions
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nfs     - boot image via network using NFS protocol
nm      - memory modify (constant address)
part    - disk partition related commands
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
spl     - SPL configuration
sspi    - SPI utility command
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true    - do nothing, successfully
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
U-Boot# printenv 
boot_targets= mmc0 nand 
bootcmd_mmc0=setenv devnum 0; setenv rootpart 2; run mmc_boot;
bootpart=0:2
ethact=cpsw
ethaddr=bc:6a:29:f7:d9:88
fdt_high=0xa0000000
loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}
mmc_boot=setenv devtype mmc; if mmc dev ${devnum}; then run mmcargs;run scan_boot; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; run mmcboot;fi
mmcboot=mmc dev ${mmcdev}; if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then echo Loaded environment from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;if run loadimage; then run mmcloados;fi;fi;
mmcrootfstype=ext4 rootwait
rootpart=2
scan_boot=echo Scanning ${devtype} ${devnum}...; for prefix in ${bootdir}; do for script in ${bootfile}; do run script_boot; done; done;
soc=am33xx
usbargs=setenv bootargs console=${console} ${optargs} root=${usbroot} rootfstype=${usbrootfstype}
usbnet_devaddr=bc:6a:29:f7:d9:89
usbroot=/dev/sda2 rw

Environment size: 1022/131067 bytes
U-Boot# printenv 
boot_targets= mmc0 nand 
bootcmd_mmc0=setenv devnum 0; setenv rootpart 2; run mmc_boot;
bootpart=0:2
console=ttyO0,115200n8
ethact=cpsw
ethaddr=bc:6a:29:f7:d9:88
fdt_high=0xa0000000
loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}
mmc_boot=setenv devtype mmc; if mmc dev ${devnum}; then run mmcargs;run scan_boot; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; run mmcboot;fi
mmcboot=mmc dev ${mmcdev}; if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then echo Loaded environment from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;if run loadimage; then run mmcloados;fi;fi;
mmcrootfstype=ext4 rootwait
rootpart=2
scan_boot=echo Scanning ${devtype} ${devnum}...; for prefix in ${bootdir}; do for script in ${bootfile}; do run script_boot; done; done;
soc=am33xx
usbargs=setenv bootargs console=${console} ${optargs} root=${usbroot} rootfstype=${usbrootfstype}
usbnet_devaddr=bc:6a:29:f7:d9:89
usbroot=/dev/sda2 rw

Environment size: 1047/131067 bytes
U-Boot# printenv 
boot_targets= mmc0 nand 
bootcmd_mmc0=setenv devnum 0; setenv rootpart 2; run mmc_boot;
bootpart=0:2
console=ttyO0,115200n8
ethact=cpsw
ethaddr=bc:6a:29:f7:d9:88
fdt_high=0xa0000000
loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}
mmc_boot=setenv devtype mmc; if mmc dev ${devnum}; then run mmcargs;run scan_boot; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; run mmcboot;fi
mmcboot=mmc dev ${mmcdev}; if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then echo Loaded environment from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;if run loadimage; then run mmcloados;fi;fi;
mmcrootfstype=ext4 rootwait
rootpart=2
scan_boot=echo Scanning ${devtype} ${devnum}...; for prefix in ${bootdir}; do for script in ${bootfile}; do run script_boot; done; done;
soc=am33xx
usbargs=setenv bootargs console=${console} ${optargs} root=${usbroot} rootfstype=${usbrootfstype}
usbnet_devaddr=bc:6a:29:f7:d9:89
usbroot=/dev/sda2 rw

Environment size: 1047/131067 bytes
U-Boot# printenv 
boot_targets= mmc0 nand 
bootcmd_mmc0=setenv devnum 0; setenv rootpart 2; run mmc_boot;
bootpart=0:2
console=ttyO0,115200n8
ethact=cpsw
ethaddr=bc:6a:29:f7:d9:88
fdt_high=0xa0000000
loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}
mmc_boot=setenv devtype mmc; if mmc dev ${devnum}; then run mmcargs;run scan_boot; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; run mmcboot;fi
mmcboot=mmc dev ${mmcdev}; if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then echo Loaded environment from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;if run loadimage; then run mmcloados;fi;fi;
mmcrootfstype=ext4 rootwait
rootpart=2
scan_boot=echo Scanning ${devtype} ${devnum}...; for prefix in ${bootdir}; do for script in ${bootfile}; do run script_boot; done; done;
soc=am33xx
usbargs=setenv bootargs console=${console} ${optargs} root=${usbroot} rootfstype=${usbrootfstype}
usbnet_devaddr=bc:6a:29:f7:d9:89
usbroot=/dev/sda2 rw

Environment size: 1047/131067 bytes
U-Boot# printenv 
boot_targets= mmc0 nand 
bootcmd_mmc0=setenv devnum 0; setenv rootpart 2; run mmc_boot;
bootpart=0:2
console=ttyO0,115200n8
ethact=cpsw
ethaddr=bc:6a:29:f7:d9:88
fdt_high=0xa0000000
loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}
mmc_boot=setenv devtype mmc; if mmc dev ${devnum}; then run mmcargs;run scan_boot; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; run mmcboot;fi
mmcboot=mmc dev ${mmcdev}; if mmc rescan; then echo SD/MMC found on device ${mmcdev};if run loadbootenv; then echo Loaded environment from ${bootenv};run importbootenv;fi;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;if run loadimage; then run mmcloados;fi;fi;
mmcrootfstype=ext4 rootwait
rootpart=2
scan_boot=echo Scanning ${devtype} ${devnum}...; for prefix in ${bootdir}; do for script in ${bootfile}; do run script_boot; done; done;
soc=am33xx
usbargs=setenv bootargs console=${console} ${optargs} root=${usbroot} rootfstype=${usbrootfstype}
usbnet_devaddr=bc:6a:29:f7:d9:89
usbroot=/dev/sda2 rw

Environment size: 1047/131067 bytes
U-Boot# reset
resetting ...
CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

musb_init_controller failed with status -22
musb_init_controller failed with status -22
board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  0 
U-Boot# reset
resetting ...
CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

musb_init_controller failed with status -22
musb_init_controller failed with status -22
board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpswdata abort

    MAYBE you should read doc/README.arm-unaligned-accesses

pc : [<9f78784c>]	   lr : [<9f787830>]
sp : 9f32ee20  ip : 9f32ee40	 fp : 9f32eea0
r10: 80844f0c  r9 : 9f32ef38	 r8 : 9ffecf20
r7 : 00000000  r6 : 9f75b4f4	 r5 : 00000000  r4 : 00000000
r3 : 9f32eea0  r2 : 00000065	 r1 : 00000000  r0 : e8aa7fa5
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32
Resetting CPU ...

resetting ...
CCCCCCCC
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1undefined instruction
pc : [<ffff1c44>]	   lr : [<9f7789f4>]
sp : 9f32e970  ip : 00000020	 fp : 80814a88
r10: 80844f0c  r9 : 9f32ef38	 r8 : 4030cdcc
r7 : 4030cb7c  r6 : 00000002	 r5 : 9f32efe0  r4 : ffff0000
r3 : 9ffbc33c  r2 : 00000001	 r1 : 9f32ef04  r0 : fffffffe
Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32
Resetting CPU ...

resetting ...
C
U-Boot SPL 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)
get_dpll_ddr_params
set_mux_conf_regs
--DEBUG-- Configuring i2c1 pinmux 
--DEBUG-- Configuring mii1 pinmux 
--DEBUG-- Configuring mmc0 pinmux 
--DEBUG-- Configuring mmc1 pinmux 
sdram_init 
am33xx_spl_board_init 
spl_board_init end 


U-Boot 2013.10-gc8185c4 (Jan 28 2016 - 10:46:57)

I2C:   ready
DRAM:  512 MiB
board_init 
NAND:  0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Error - No Valid Environment Area found
*** Warning - bad CRC, using default environment

musb_init_controller failed with status -22
musb_init_controller failed with status -22
board_late_init 
Net:   board_eth_init 
<ethaddr> not set. Validating first E-fuse MAC
Could not get PHY for cpsw: addr 0
cpsw, usb_ether
Hit any key to stop autoboot:  0 
U-Boot#

Activity

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Metadata

Metadata

Assignees

No one assigned

    Labels

    No labels
    No labels

    Projects

    No projects

      Milestone

      No milestone

      Relationships

      None yet

      Development

      No branches or pull requests

      Issue actions